KFAS: Fanuc CNC Parts, Service, & Repair
Fanuc Series 16i/ 18i Troubleshooting Information/ Procedures/ Alarms
Fanuc 16i/ 18i Maintenance Manual: B-63005E
How to replace control cooling fan: LCD mounted type Stand-alone type
Watch video on how to replace cooling fan
LCD Back light replacement information
CRT Blank (Nothing is displayed on the CRT)
Alarm List and Description
Absolute Pulse Coder (APC) Alarms (Alarm 300, 301, 302, 303, 304, 305, 306, 307, 308, 309)
Troubleshooting Steps Alarm 301 to 305 Alarm 306 to 308
Serial Pulse Coder (SPC) Alarms (Alarm 350, 351)
Troubleshooting Steps Alarm 350 Alarm 351
Servo Alarms (Alarm 400, 401, 404, 405, 407, 409, 410, 411, 413, 414, 415, 416, 417, 420, 421)
Troubleshooting Steps Alarm 400 Alarm 401 Alarm 404 and 405
Alarm 410 Alarm 411 Alarm 414 (with A06B-6066-Hxxx servo)
Alarm 414 (with A06B-6096-Hxxx servo)
Over travel alarms (Alarm 500, 501, 502, 503,, 504, 505, 506, 507, 508, 509, 510, 511)
Overheat alarms (Alarm 700, 701, 704)
Troubleshooting Steps Alarm 700, 701 How to replace control cooling fan
Serial Spindle Alarms (Alarm 749, 750, 751, 752, 754, 761, 762, 764, 771, 772, 774)
Troubleshooting Steps Alarm 749 Alarm 750 Alarm 751 and 761
(with A06B-6088-Hxxx spindle unit)
(With A06B-6064, 6063 spindle unit)
System Alarms (Alarm 900, 914, 915, 916, 920, 922, 924, 930, 950, 951, 972, 973, 974, 975)
Troubleshooting Steps Alarm 900 Alarm 914, 915 Alarm 916 Alarm 920, 922
Alarm 924 Alarm 930 Alarm 950 Alarm 951
Other useful Fanuc 16/18 Manuals
63002EN Description Manual
63003ENC Hardware Connection
0 PLEASE TURN OFF POWER
1 TH PARITY ALARM
2 TV PARITY ALARM
3 TOO MANY DIGITS
4 ADDRESS NOT FOUND
5 NO DATA AFTER ADDRESS
6 ILLEGAL USE OF NEGATIVE SIGN
7 ILLEGAL USE OF DECIMAL POINT
9 ILLEGAL ADDRESS INPUT
10 IMPROPER G–CODE
11 NO FEEDRATE COMMANDED
14 CAN NOT COMMAND G95 (M series)
14 ILLEGAL LEAD COMMAND (T series)
15 TOO MANY AXES COMMANDED (M series)
15 TOO MANY AXES COMMANDED (T series)
20 OVER TOLERANCE OF RADIUS
21 ILLEGAL PLANE AXIS COMMANDED
22 NO CIRCLE RADIUS
23 ILLEGAL RADIUS COMMAND (T series)
25 CANNOT COMMAND F0 IN G02/G03 (M series)
27 NO AXES COMMANDED IN G43/G44 (M series)
28 ILLEGAL PLANE SELECT
29 ILLEGAL OFFSET VALUE (M series)
29 ILLEGAL OFFSET VALUE (T series)
30 ILLEGAL OFFSET NUMBER (M series)
30 ILLEGAL OFFSET NUMBER (T series)
31 ILLEGAL P COMMAND IN G10
32 ILLEGAL OFFSET VALUE IN G10
33 NO SOLUTION AT CRC (M series)
33 NO SOLUTION AT CRC (T series)
34 NO CIRC ALLOWED IN ST–UP /EXT BLK (M series)
34 NO CIRC ALLOWED IN ST–UP /EXT BLK (T series)
35 CAN NOT COMMANDED G31 (T series)
35 CAN NOT COMMANDED G39 (M series)
36 CAN NOT COMMANDED G31 (M series)
37 CAN NOT CHANGE PLANE IN CRC (M seires)
37 CAN NOT CHANGE PLANE IN NRC (T seires)
38 INTERFERENCE IN CIRCULAR BLOCK (M seires)
38 INTERFERENCE IN CIRCULAR BLOCK (T series)
39 CHF/CNR NOT ALLOWED IN NRC (T series)
40 INTERFERENCE IN G90/G94 BLOCK (T series)
41 INTERFERENCE IN CRC (M seires)
41 INTERFERENCE IN NRC (T seires)
42 G45/G48 NOT ALLOWED IN CRC (M series)
44 G27–G30 NOT ALLOWED IN FIXED CYC (M series)
45 ADDRESS Q NOT FOUND (G73/G83) (M series)
46 ILLEGAL REFERENCE RETURN COMMAND
47 ILLEGAL AXIS SELECT
48 BASIC 3 AXIS NOT FOUND
49 ILLEGAL OPERATION (G68/G69) (M series)
50 CHF/CNR NOT ALLOWED IN THRD BLK (M series)
50 CHF/CNR NOT ALLOWED IN THRD BLK(T series)
51 MISSING MOVE AFTER CHF/CNR (M series)
51 MISSING MOVE AFTER CHF/CNR (T series)
52 CODE IS NOT G01 AFTER CHF/CNR (M series)
52 CODE IS NOT G01 AFTER CHF/CNR (T series)
53 TOO MANY ADDRESS COMMANDS (M series)
53 TOO MANY ADDRESS COMMANDS (T seires)
54 NO TAPER ALLOWED AFTER CHF/CNR (T series)
55 MISSING MOVE VALUE IN CHF/CNR (M series)
55 MISSING MOVE VALUE IN CHF/CNR (T series)
56 NO END POINT & ANGLE IN CHF/CNR (T series)
57 NO SOLUTION OF BLOCK END (T series)
58 END POINT NOT FOUND (M series)
58 END POINT NOT FOUND (T series)
59 PROGRAM NUMBER NOT FOUND
60 SEQUENCE NUMBER NOT FOUND
61 ADDRESS P/Q NOT FOUND IN G70–G73 (T series)
62 ILLEGAL COMMAND IN G71–G76 (T series)
63 SEQUENCE NUMBER NOT FOUND (T series)
64 SHAPE PROGRAM NOT MONOTONOUSLY (T series)
65 ILLEGAL COMMAND IN G71–G73 (T series)
66 IMPROPER G–CODE IN G71–G73 (T series)
67 CAN NOT ERROR IN MDI MODE (T series)
69 FORMAT ERROR IN G70–G73 (T series)
70 NO PROGRAM SPACE IN MEMORY
71 DATA NOT FOUND
72 TOO MANY PROGRAMS
73 PROGRAM NUMBER ALREADY IN
74 ILLEGAL PROGRAM NUMBER
75 PROTECT
76 ADDRESS P NOT DEFINED
77 SUB PROGRAM NESTING ERROR
78 NUMBER NOT FOUND
79 PROGRAM VERIFY ERROR
80 G37 ARRIVAL SIGNAL NOT ASSERTED (M series)
80 G37 ARRIVAL SIGNAL NOT ASSERTED (T series)
81 OFFSET NUMBER NOT FOUND IN G37 (M series)
81 OFFSET NUMBER NOT FOUND IN G37 (T series)
82 H–CODE NOT ALLOWED IN G37 (M series)
82 T–CODE NOT ALLOWED IN G37 (T series)
83 ILLEGAL AXIS COMMAND IN G37 (M series)
83 ILLEGAL AXIS COMMAND IN G37 (T series)
85 COMMUNICATION ERROR
86 DR SIGNAL OFF
87 BUFFER OVERFLOW
88 LAN FILE TRANS ERROR (CHANNEL–1)
89 LAN FILE TRANS ERROR (CHANNEL–2)
90 REFERENCE RETURN INCOMPLETE
91 REFERENCE RETURN INCOMPLETE
92 AXES NOT ON THE REFERENCE POINT
94 P TYPE NOT ALLOWED (COORD CHG)
95 P TYPE NOT ALLOWED (EXT OFS CHG)
96 P TYPE NOT ALLOWED (WRK OFS CHG)
97 P TYPE NOT ALLOWED (AUTO EXEC)
98 G28 FOUND IN SEQUENCE RETURN
99 MDI EXEC NOT ALLOWED AFT. SEARCH
100 PARAMETER WRITE ENABLE
101 PLEASE CLEAR MEMORY
109 FORMAT ERROR IN G08 (M series)
110 DATA OVERFLOW
111 CALCULATED DATA OVERFLOW
112 DIVIDED BY ZERO
113 IMPROPER COMMAND
114 FORMAT ERROR IN MACRO
115 ILLEGAL VARIABLE NUMBER
116 WRITE PROTECTED VARIABLE
118 PARENTHESIS NESTING ERROR
119 ILLEGAL ARGUMENT
122 FOUR FOLD MACRO MODAL–CALL
123 CAN NOT USE MACRO COMMAND IN DNC
124 MISSING END STATEMENT
125 FORMAT ERROR IN MACRO
126 ILLEGAL LOOP NUMBER
127 NC, MACRO STATEMENT IN SAME BLOCK
128 ILLEGAL MACRO SEQUENCE NUMBER
129 ILLEGAL ARGUMENT ADDRESS
130 ILLEGAL AXIS OPERATION
131 TOO MANY EXTERNAL ALARM MESSAGES
132 ALARM NUMBER NOT FOUND
133 ILLEGAL DATA IN EXT. ALARM MSG
135 ILLEGAL ANGLE COMMAND (M series)
135 SPINDLE ORIENTATION PLEASE (T series)
136 C/H–CODE & MOVE CMD IN SAME BLK. (T series)
136 ILLEGAL AXIS COMMAND (M series)
137 M–CODE & MOVE CMD IN SAME BLK.
138 SUPERIMPOSED DATA OVERFLOW
139 CAN NOT CHANGE PMC CONTROL AXIS
141 CAN NOT COMMAND G51 IN CRC (M series)
142 ILLEGAL SCALE RATE (M series)
143 SCALED MOTION DATA OVERFLOW (M series)
144 ILLEGAL PLANE SELECTED (M series)
145 ILLEGAL CONDITIONS IN POLAR COORDINATE INTERPOLATION
146 IMPROPER G CODE
148 ILLEGAL SETTING DATA (M series)
149 FORMAT ERROR IN G10L3 (M series)
150 ILLEGAL TOOL GROUP NUMBER
151 TOOL GROUP NUMBER NOT FOUND
152 NO SPACE FOR TOOL ENTRY
153 T–CODE NOT FOUND
154 NOT USING TOOL IN LIFE GROUP (M series)
155 ILLEGAL T–CODE IN M06 (M series)
155 ILLEGAL T–CODE IN M06 (T series)
156 P/L COMMAND NOT FOUND
157 TOO MANY TOOL GROUPS
158 ILLEGAL TOOL LIFE DATA
159 TOOL DATA SETTING INCOMPLETE
163 COMMAND G68/G69 INDEPENDENTLY T series (At two–path)
175 ILLEGAL G107 COMMAND
176 IMPROPER G–CODE IN G107 (M series)
176 IMPROPER G–CODE IN G107 (T series)
177 CHECK SUM ERROR (G05 MODE)
178 G05 COMMANDED IN G41/G42 MODE
179 PARAM. (NO. 7510) SETTING ERROR
180 COMMUNICATION ERROR (REMOTE BUF)
181 FORMAT ERROR IN G81 BLOCK (Hobbing machine, EGB) (M series)
182 G81 NOT COMMANDED (Hobbing machine) (M series)
183 DUPLICATE G83 (COMMANDS) (Hobbing machine) (M series)
184 ILLEGAL COMMAND IN G81 (Hobbing machine, EGB) (M series)
185 RETURN TO REFERENCE POINT (Hobbing machine) (M series)
186 PARAMETER SETTING ERROR (Hobbing machine, EGB) (M series)
187 HOB COMMAND IS NOT ALLOWED
190 ILLEGAL AXIS SELECT (M series)
194 SPINDLE COMMAND IN SYNCHRO–MODE
195 MODE CHANGE ERROR
197 C–AXIS COMMANDED IN SPINDLE MODE
199 MACRO WORD UNDEFINED
200 ILLEGAL S CODE COMMAND
201 FEEDRATE NOT FOUND IN RIGID TAP
202 POSITION LSI OVERFLOW
203 PROGRAM MISS AT RIGID TAPPING
204 ILLEGAL AXIS OPERATION
205 RIGID MODE DI SIGNAL OFF
206 CAN NOT CHANGE PLANE (RIGID TAP) (M series)
207 RIGID DATA MISMATCH
210 CAN NOT COMAND M198/M199
211 G31 (HIGH) NOT ALLOWED IN G99
212 ILLEGAL PLANE SELECT (M series)
212 ILLEGAL PLANE SELECT (T series)
213 ILLEGAL COMMAND IN SYNCHRO–MODE
213 ILLEGAL COMMAND IN SYNCHRO–MODE (T series)
214 ILLEGAL COMMAND IN SYNCHRO–MODE
217 DUPLICATE G51.2 (COMMANDS) (T series)
218 NOT FOUND P/Q COMMAND IN G251 (T series)
219 COMMAND G250/G251 INDEPENDENTLY (T series)
220 ILLEGAL COMMAND IN SYNCHR–MODE (T series)
221 ILLEGAL COMMAND IN SYNCHR–MODE (T series)
222 DNC OP. NOT ALLOWED IN BG.–EDIT (M series)
224 RETURN TO REFERENCE POINT (M series)
224 RETURN TO REFERENCE POINT (T series)
225 SYNCHRONOUS/MIXED CONTROL ERROR (T series (At two–path))
226 ILLEGAL COMMAND IN SYNCHRO– MODE (T series (At two–path))
229 CAN NOT KEEP SYNCHRO–STATE (T series)
230 R CODE NOT FOUND (Grinding machine) (M series)
231 ILLEGAL FORMAT IN G10 OR L50
233 DEVICE BUSY
239 BP/S ALARM
240 BP/S ALARM
244 P/S ALARM (T series)
245 T–CODE NOT ALOWEE IN THIS BLOCK (T series)
251 ATC ERROR (M series)
252 ATC SPINDLE ALARM (M series)
253 G05 IS NOT AVAILABLE (M series)
300 n AXIS NEED ZRN
301 APC ALARM:n AXIS COMMUNICATION
302 APC ALARM:n AXIS OVER TIME
303 APC ALARM:n AXIS FRAMING
304 APC ALARM:n AXIS PARITY
305 APC ALARM:n AXIS PULSE MISS
306 APC ALARM:n AXIS BATTERY ZERO
307 APC ALARM:n AXIS BATTERY DOWN 1
308 APC ALARM:n AXIS BATTERY DOWN 2
309 APC ALARM:n AXIS ZRN IMPOSSIBLE
360 n AXIS : ABNORMAL CHECKSUM (INT)
361 n AXIS : ABNORMAL PHASE DATA (INT)
362 n AXIS : ABNORMAL REV.DATA (INT)
363 n AXIS : ABNORMAL CLOCK (INT)
364 n AXIS : SOFT PHASE ALARM (INT)
365 n AXIS : BROKEN LED (INT)
366 n AXIS : PULSE MISS (INT)
367 n AXIS : COUNT MISS (INT)
368 n AXIS : SERIAL DATA ERROR (INT)
369 n AXIS : DATA TRANS. ERROR (INT)
380 n AXIS : BROKEN LED (EXT)
381 n AXIS : ABNORMAL PHASE (EXT LIN)
382 n AXIS : COUNT MISS (EXT)
383 n AXIS : PULSE MISS (EXT)
384 n AXIS : SOFT PHASE ALARM (EXT)
385 n AXIS : SERIAL DATA ERROR (EXT)
386 n AXIS : DATA TRANS. ERROR (EXT)
387 n AXIS : ABNORMAL ENCODER (EXT)
400 SERVO ALARM: n–TH AXIS OVERLOAD
401 SERVO ALARM: n–TH AXIS VRDY OFF
402 SERVO ALARM: SV CARD NOT EXIST
403 SERVO ALARM: CARD/SOFT MISMATCH
404 SERVO ALARM: n–TH AXIS VRDY ON
405 SERVO ALARM: (ZERO POINT RETURN FAULT)
407 SERVO ALARM: EXCESS ERROR
409 SERVO ALARM: n AXIS TORQUE ALM
410 SERVO ALARM: n–TH AXIS – EXCESS ERROR
411 SERVO ALARM: n–TH AXIS – EXCESS ERROR
413 SERVO ALARM: n–th AXIS – LSI OVERFLOW
414 SERVO ALARM: n–TH AXIS – DETECTION RELATED ERROR
415 SERVO ALARM: n–TH AXIS – EXCESS SHIFT
416 SERVO ALARM: n–TH AXIS – DISCONNECTION
417 SERVO ALARM: n–TH AXIS – PARAMETER INCORRECT
420 SERVO ALARM: n AXIS SYNC TORQUE (M series)
421 SERVO ALARM: n AXIS EXCESS ER (D)
422 SERVO ALARM: n AXIS
423 SERVO ALARM: n AXIS
430 n AXIS : SV. MOTOR OVERHEAT
431 n AXIS : CNV. OVERLOAD
432 n AXIS : CNV. LOW VOLT CONTROL
433 n AXIS : CNV. LOW VOLT DC LINK
434 n AXIS : INV. LOW VOLT CONTROL
435 n AXIS : INV. LOW VOLT DC LINK
436 n AXIS : SOFTTHERMAL (OVC)
437 n AXIS : CNV. OVERCURRENT POWER
438 n AXIS : INV. ABNORMAL CURRENT
439 n AXIS : CNV. OVER VOLT DC LINK
440 n AXIS : CNV. EX DECELERATION POW.
441 n AXIS : ABNORMAL CURRENT OFFSET
442 n AXIS : CNV. CHARGE FAILURE
443 n AXIS : CNV. COOLING FAN FAILURE
444 n AXIS : INV. COOLING FAN FAILURE
445 n AXIS : SOFT DISCONNECT ALARM
446 n AXIS : HARD DISCONNECT ALARM
447 n AXIS : HARD DISCONNECT (EXT)
448 n AXIS : UNMATCHED FEEDBACK ALARM
449 n AXIS : INV. IPM ALARM
453 n AXIS : SPC SOFT DISCONNECT ALARM
456 n AXIS : ILLEGAL CURRENT LOOP
457 n AXIS : ILLEGAL HI HRV (250US)
458 n AXIS : CURRENT LOOP ERROR
459 n AXIS : HI HRV SETTING ERROR
460 n AXIS : FSSB DISCONNECT
461 n AXIS : ILLEGAL AMP INTERFACE
462 n AXIS : SEND CNC DATA FAILED
463 n AXIS : SEND SLAVE DATA FAILED
464 n AXIS : WRITE ID DATA FAILED
465 n AXIS : READ ID DATA FAILED
466 n AXIS : MOTOR/AMP COMBINATION
467 n AXIS : ILLEGAL SETTING OF AXIS
468 n AXIS : HI HRV SETTING ERROR (AMP)
500 OVER TRAVEL : +n
501 OVER TRAVEL : –n
502 OVER TRAVEL : +n
503 OVER TRAVEL : –n
504 OVER TRAVEL : +n
505 OVER TRAVEL : –n
506 OVER TRAVEL : +n
507 OVER TRAVEL : –n
700 OVERHEAT: CONTROL UNIT
701 OVERHEAT: FAN MOTOR
704 OVERHEAT: SPINDLE
740 RIGID TAP ALARM : EXCESS ERROR
741 RIGID TAP ALARM : EXCESS ERROR
742 RIGID TAP ALARM : LSI OVER FLOW
749 S–SPINDLE LSI ERROR
750 SPINDLE SERIAL LINK START FAULT
751 FIRST SPINDLE ALARM DETECTION (AL–XX)
752 FIRST SPINDLE MODE CHANGE FAULT
754 SPINDLE–1 ABNORMAL TORQUE ALM
761 SECOND SPINDLE ALARM DETECTION (AL–XX)
762 SECOND SPINDLE MODE CHANGE FAULT
764 SPINDLE–2 ABNORMAL TORQUE ALM
771 SPINDLE–3 ALARM DETECT (AL–XX)
772 SPINDLE–3 MODE CHANGE ERROR
774 SPINDLE–3 ABNORMAL TORQUE ALM
782 SPINDLE–4 MODE CHANGE ERROR
784 SPINDLE–4 ABNORMAL TORQUE ALM
900 ROM PARITY
910 SRAM PARITY : (BYTE 0)
911 SRAM PARITY : (BYTE 1)
912 DRAM PARITY : (BYTE 0)
913 DRAM PARITY : (BYTE 1)
914 DRAM PARITY : (BYTE 2)
915 DRAM PARITY : (BYTE 3)
916 DRAM PARITY : (BYTE 4)
917 DRAM PARITY : (BYTE 5)
918 DRAM PARITY : (BYTE 6)
919 DRAM PARITY : (BYTE 7)
920 SERVO ALARM (1–4 AXIS)
921 SERVO ALARM (5–8 AXIS)
926 FSSB ALARM
930 CPU INTERRUPUT
935 SRAM ECC ERROR
950 PMC SYSTEM ALARM
951 PMC WATCH DOG ALARM
970 NMI OCCURRED IN PMCLSI
971 NMI OCCURRED IN SLC
972 NMI OCCURRED IN OTHER MODULE
973 NON MASK INTERRUPT
974 F–BUS ERROR
975 BUS ERROR
976 L–BUS ERROR
4500 REPOSITIONING INHIBITED
4502 ILLEGAL COMMAND IN BOLT HOLE
4503 ILLEGAL COMMAND IN LINE AT ANGLE
4504 ILLEGAL COMMAND IN ARC
4505 ILLEGAL COMMAND IN GRID
4506 ILLEGAL COMMAND IN SHARE PROOFS
4507 ILLEGAL COMMAND IN SQUARE
4508 ILLEGAL COMMAND IN RADIUS
4509 ILLEGAL COMMAND IN CUT AT ANGLE
4510 ILLEGAL COMMAND IN LINE-PUNCH
4511 ILLEGAL COMMAND IN CIRCLE-PUNCH
4520 T, M INHIBITED IN NIBBLING-MODE
4521 EXCESS NIBBLING MOVEMENT (X, Y)
4522 EXCESS NIBBLING MOVEMENT (C)
4523 ILLEGAL COMMAND IN CIRCLE-NIBBL
4524 ILLEGAL COMMAND IN LINE-NIBBL
4530 A/B MACRO NUMBER ERROR
4531 U/V MACRO FORMAT ERROR
4532 IMPROPER U/V MACRO NUMBER
4533 U/V MACRO MEMORY OVERFLOW
4534 W MACRO NUMBER NOT FOUND
4535 U/V MACRO NESTING ERROR
4536 NO W, Q COMMAND IN MULTI-PIECE
4537 ILLEGAL Q VALUE IN MULTI-PIECE
4538 W NO. NOT FOUND IN MULTI-PIECE
4539 MULTI-PIECE SETTING IS ZERO
4540 MULTI-PIECE COMMAND WITHIN MACRO
4542 MULTI-PIECE COMMAND ERROR
4543 MULTI-PIECE Q COMMAND ERROR
4544 MULTI-PIECE RESTART ERROR
4549 ILLEGAL TOOL DATA FORMAT
4600 T, C COMMAND IN INTERPOLATION
4601 INHIBITED T, M COMMAND
4602 ILLEGAL T-CODE
4603 C AXIS SYNCHRONOUS ERROR
4604 ILLEGAL AXIS OPERATION
4605 NEED ZRN
4630 ILLEGAL COMMAND IN LASER MODE
4650 IMPROPER G-CODE IN OFFSET MODE
4700 PROGRAM ERROR (OT +)
4701 PROGRAM ERROR (OT –)
4702 PROGRAM ERROR (OT +)
4703 PROGRAM ERROR (OT –)
4704 PROGRAM ERROR (OT +)
4705 PROGRAM ERROR (OT –)
4815 ZONE : ENTERING INHIBITED 3 –X
5000 ILLEGAL COMMAND CODE (M series)
5003 ILLEGAL PARAMETER (HPCC) (M series)
5004 HPCC NOT READY
5006 TOO MANY WORD IN ONE BLOCK (M series)
5007 TOO LARGE DISTANCE (M series)
5009 PARAMETER ZERO (DRY RUN) (M series)
5010 END OF RECORD
5012 G05 P10000 ILLEGAL START UP (HPCC) (M series)
5013 HPCC: CRC OFS REMAIN AT CANCEL (M series)
5014 TRACE DATA NOT FOUND (M series)
5018 POLYGON SPINDLE SPEED ERROR (T series)
5020 PARAMETER OF RESTART ERROR
5030 ILLEGAL COMMAND (G100) (T series)
5031 ILLEGAL COMMAND (G100, G102, G103) (T series)
5032 NEW PRG REGISTERED IN B–AXS MOVE (T series)
5033 NO PROG SPACE IN MEMORY B–AXS (T series)
5034 PLURAL COMMAND IN G110 (T series)
5035 NO FEEDRATE COMMANDED B–AXS (T series)
5036 ADDRESS R NOT DEFINED IN G81–G86 (T series)
5037 ADDRESS Q NOT DEFINED IN G83 (T series)
5038 TOO MANY START M–CODE COMMAND (T series)
5039 START UNREGISTERED B–AXS PROG (T series)
5040 CAN NOT COMMANDED B–AXS MOVE (T series)
5041 CAN NOT COMMANDED G110 BLOCK (T series)
5044 G68 FORMAT ERROR (M series)
5046 ILLEGAL PARAMETER (ST.COMP)
5050 ILL–COMMAND IN CHOPPING MODE (M series)
5051 M–NET CODE ERROR
5052 M–NET ETX ERROR
5053 M–NET CONNECT ERROR
5054 M–NET RECEIVE ERROR
5055 M–NET PRT/FRT ERROR
5057 M–NET BOARD SYSTEM DOWN
5058 G35/G36 FORMAT ERROR (T series)
5059 RADIUS IS OUT OF RANGE
5059 RADIUS IS OUT OF RANGE (T series)
5060 ILLEGAL PARAMETER IN G02.3/G03.3 (M series)
5061 ILLEGAL FORMAT IN G02.3/G03.3 (M series)
5062 ILLEGAL COMMAND IN G02.3/G03.3
5063 IS NOT PRESET AFTER REF. (M series)
5064 DIFFERENT AXIS UNIT (IS–B, IS–C)
5065 DIFFERENT AXIS UNIT (PMC AXIS) (M series)
5067 (HPCC) (M series)
5068 G31 FORMAT ERROR (M series)
5069 WHL–C:ILLEGA P–DATA (M series)
5073 NO DECIMAL POINT
5074 ADDRESS DUPLICATION ERROR
5082 DATA SERVER ERROR
5085 SMOOTH IPL ERROR 1
5096 MISMATCH WAITING M–CODE
5110 IMPROPER G–CODE (G05.1 G1 MODE) (M series)
5111 IMPROPER MODAL G–CODE (G05.1 G1) (M series)
5112 G08 CAN NOT BE COMMANDED (G05.1 G1) (M series)
5113 CAN NOT ERROR IN MDI MODE (G05.1) (M series)
5114 NOT STOP POSITION (G05.1 Q1) (M series)
5115 SPL : ERROR (M series)
5116 SPL : ERROR (M series)
5117 SPL : ERROR (M series)
5118 SPL : ERROR (M series)
5122 ILLEGAL COMMAND IN SPIRAL (M series)
5123 OVER TOLERANCE OF END POINT (M series)
5124 CAN NOT COMMAND SPIRAL (M series)
5134 FSSB : OPEN READY TIME OUT
5135 FSSB : ERROR MODE
5136 FSSB : NUMBER OF AMPS IS SMALL
5137 FSSB : CONFIGURATION ERROR
5138 FSSB : AXIS SETTING NOT COMPLETE
5139 FSSB : ERROR
5155 NOT RESTART PROGRAM BY G05
5156 ILLEGAL AXIS OPERATION (M series)
5157 PARAMETER ZERO (M series)
5195 DIRECTION CAN NOT BE JUDGED (T series)
5196 ILLEGAL OPERATION (HPCC) (M series)
5197 FSSB : OPEN TIME OUT
5198 FSSB : ID DATA NOT READ
5199 FINE TORQUE SENSING PARAMETER
5212 SCREEN COPY : PARAMETER ERROR
5213 SCREEN COPY : COMMUNICATION ERROR
5214 SCREEN COPY : DATA TRANSFER ERROR
5218 ILLEGAL PARAMETER (INCL. COMP)
5219 CAN NOT RETURN
5220 REFERENCE POINT ADJUSTMENT MODE
5222 SRAM CORRECTABLE ERROR
5227 FILE NOT FOUND
5228 SAME NAME USED
5229 WRITE PROTECTED
5231 TOO MANY FILES
5232 DATA OVER–FLOW
5235 COMMUNICATION ERROR
5237 READ ERROR
5238 WRITE ERROR
5242 ILLEGAL AXIS NUMBER (M series)
5243 DATA OUT OF RANGE (M series)
5244 TOO MANY DI ON (M series)
5245 OTHER AXIS ARE COMMANDED (M series)
5251 ILLEGAL PARAMETER IN G54.2 (M series)
5252 ILLEGAL P COMMAND IN G54.2 (M series)
5257 G41/G42 NOT ALLOWED IN MDI MODE (M series)
5257 G41/G42 NOT ALLOWED IN MDI MODE (T series)
5300 SET ALL OFFSET DATAS AGAIN
5302 ILLEGAL COMMAND IN G68 MODE
5303 TOUCH PANEL ERROR
5306 MODE CHANGE ERROR
5307 INTERNAL DATA OVER FLOW (M series)
5311 FSSB: ILLEGAL CONNECTION
5321 S–COMP. VALUE OVERFLOW
5400 SPL: ILLEGAL AXIS COMMAND (M series)
5401 SPL: ILLEGAL COMMAND (M series)
5402 SPL: ILLEGAL AXIS MOVING (M series)
5403 SPL: CAN NOT MAKE VECTOR (M series)
5405 ILLEGAL PARAMETER IN G41.2/ G42.2 (M series)
5406 G41.3/G40 FORMAT ERROR (M series)
5407 ILLEGAL COMMAND IN G41.3 (M series)
5408 G41.3 ILLEGAL START_UP (M series)
5409 ILLEGAL PARAMETER IN G41.3 (M series)
5411 NURBS: ILLEGAL ORDER (M series)
5412 NURBS: NO KNOT COMMAND (M series)
5413 NURBS: ILLEGAL AXIS COMMAND (M series)
5414 NURBS: ILLEGAL KNOT (M series)
5415 NURBS: ILLEGAL CANCEL (M series)
5416 NURBS: ILLEGAL MODE (M series)
5417 NURBS: ILLEGAL MULTI–KNOT (M series)
5418 NURBS: ILLEGAL KNOT VALUE (M series)
5420 ILLEGAL PARAMETER IN G43.4/ G43.5 (M series)
5421 ILLEGAL COMMAND IN G43.4/ G43.5 (M series)
5422 EXCESS VELOCITY IN G43.4/ G43.5 (M series)
5425 ILLEGAL OFFSET VALUE (M series)
5430 ILLEGAL COMMAND IN 3–D CIR (M series)
5432 G02.4/G03.4 FORMAT ERROR (M series)
5433 MANUAL INTERVENTION IN 3–D CIR (M series)
5435 PARAMETER OUT OF RANGE (TLAC) (M series)
5436 PARAMETER SETTING ERROR 1 (TLAC) (M series)
5437 PARAMETER SETTING ERROR 2 (TLAC) (M series)
5440 ILLEGAL DRILLING AXIS SELECTED (M series)
5445 CRC: MOTION IN G39 (M series)
5446 CRC: NO AVOIDANCE (M series)
5447 CRC: DANGEROUS AVOIDANCE (M series)
5448 CRC: INTERFERENCE TO AVD. (M series)
5452 IMPROPER G–CODE (5AXIS MODE) (M series)
5453 NOTE: G68 IS CANCELED (HPCC) (M series)
5455 ILLEGAL ACC. PARAMETER (M series)
4800 ZONE: PUNCHING INHIBITED 1
4801 ZONE: PUNCHING INHIBITED 2
4802 ZONE: PUNCHING INHIBITED 3
4803 ZONE: PUNCHING INHIBITED 4
4804 ZONE: ENTERING INHIBITED 1 +X
4805 ZONE: ENTERING INHIBITED 1 –X
4806 ZONE: ENTERING INHIBITED 2 +X
4807 ZONE: ENTERING INHIBITED 2 –X
4808 ZONE: ENTERING INHIBITED 3 +X
4809 ZONE: ENTERING INHIBITED 4 +X
4810 ZONE: ENTERING INHIBITED 4 –X
4811 ZONE: ENTERING INHIBITED 1 +Y
4812 ZONE: ENTERING INHIBITED 1 –Y
4813 ZONE: ENTERING INHIBITED 2 +Y
4814 ZONE: ENTERING INHIBITED 2 –Y
4815 ZONE: ENTERING INHIBITED 3 +Y
4816 ZONE: ENTERING INHIBITED 3 –Y
4817 ZONE: ENTERING INHIBITED 4 +Y
4818 ZONE: ENTERING INHIBITED 4 –Y
4870 AUTO SETTING FEED ERROR
4871 AUTO SETTING PIECES ERROR
4872 AUTO SETTING COMMAND ERROR
Fanuc CNC Alarm App for your smart phone
© Copyright KFASLLC Houston, Texas, USA